Leading 10 usual forklift accidents ， forklift procedure need to pay attention to these issues ！.

Do not take too lightly the forklift at the office. If the operation is bad, there will certainly be significant crashes in mins, and there are many accidents involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers utilized their body weight as the weight, which almost caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and hangs on the roadside rack, which virtually triggers an mishap.
Case 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift lifts the personnel unlawfully, the forklift vehicle driver does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift rolls over.
Instance 7: The forklift chauffeur did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the chauffeur needs to first validate that the load is secure and reputable.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles overhead. When the lots is traveling, the fork should not be elevated too high, which will impact the security of the forklift. .
3. After dumping, the fork ought to be reduced to the regular driving position before driving. .
4. When turning, if there are pedestrians or lorries close by, the driving signal should be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will trigger the automobile to shed side security and tip over. .
5. When the forklift is downhill, it is strictly forbidden to shut off the fire and slide, and it is prohibited to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and have to maintain a particular safety and security range from the vehicle in front. .
7. When the forklift is running, the load must be in the most affordable placement that does not hinder the driving, and the gantry should be properly tilted back. The tons shall not be raised except when stacking or filling. .
8. The elevation of the lots have to not obstruct the chauffeur's sight. In special circumstances, when the thing influences the forward vision, drive at a reduced rate when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it needs to drive safely at a low rate when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is prohibited for workers to stand on the fork to hold things and play a stabilizing function. .
12. If problems are located, they will certainly be repaired and reported in a prompt way, and they will never ever run with diseases or conceal them.

filling and discharging.
1. When fork-loading items, the range between both forks must be adjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of loading and dumping items, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch various other goods or items. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be slanted forward somewhat when the lots is lowered to enable very easy positioning of the load and extraction of Electric Forklift Truck for Warehouse the forks. .
6. It is restricted to fork goods at high speed and hit tough things with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so regarding avoid the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping crashes. .
9. It is not allowed to use the brake inertia to slip, put, round or roll objects. .
10. It is not enabled to utilize forks to choose, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake handle to dead or depress the parking brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and Electric Forklift Truck for Warehouse after the forklift operation, the appearance should be checked, and gas, lubing oil and air conditioning water ought to be added.
2. Check the safety and security efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leakage ought to also be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across someone before you throughout driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the tendency of " cost-free turning";.
6. Adding and down the slope should be sluggish and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the car needs to be driven backwards when worsening;.
8. When the forklift workers lug the goods and progress, if they run into big or hefty goods and most likely to the driver's view, they should take the turning around workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Auto parking is not allowed under the list below problems.
1. Contours, slim roads, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the opposite side of the area with the very same size as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844